Where To Get 12v Power For Backup Camera

Download Article

A rear-view camera, also known as a backup photographic camera, lets you see what's behind your vehicle without having to wait backwards. Though the device comes standard with many new car models, yous tin can add a rear-view camera to your vehicle if it didn't come with one.

1
Buy a mountable backup camera for your specific vehicle. For safety, make sure y'all purchase a device specifically designed to exist a rear-view camera. Purchasing 1 made for your specific vehicle will brand it easier to install than a standard aftermarket camera. So you lot can install information technology easily, await for a camera that mounts onto or directly behind your license plate.^[1]
- Look for fill-in cameras at consumer electronics stores.
ii
Get an external monitor if y'all want to continue your existing rear-view mirror. An external backup monitor is a minor video screen that mounts onto your windshield similarly to a GPS. Though they have up more infinite than internal monitors, external monitors are far easier to encounter and can exist easily replaced if necessary.
- If yous'd like, you tin can use a standard video monitor instead. Even so, keep in heed that information technology may not take however features as devices designed for utilize with backup cameras.
Advertizement
3
Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully performance rear-view mirror that houses a small screen inside the drinking glass. Some internal monitors clip on top of your current rear-view mirror, but others replace your original mirror entirely.^[2]
- Virtually internal monitors shut off and disappear when not in apply, making them a perfect option if you want to preserve your car'southward looks.
4
Buy ability and video cords if your photographic camera and monitor didn't include them. For nigh rear-view camera installations, yous'll demand camera and monitor splitter cords with connectors for video and power cables, ii bare wire power cables, and an RCA video cable.^[3]
- Most installation kits include these cables, but some may require you to buy them separately.
- Some camera models use wireless transmitters instead of standard video cables.
Advertising

1
Have off your rear license plate. Using a Phillips head screwdriver, remove each of the screws holding your rear license plate in place. And then, pull the plate off and set information technology aside.^[iv]
- Make sure you place the screws in a prophylactic place then yous don't lose them.
2
Remove your trunk's interior console. Pop open your torso and look for a solid interior panel roofing the opposite side of your license plate mounting expanse. And so, insert a trim removal tool or other thin device backside the panel and pry it off.^[v]
- Removing this panel will expose the car's rear wiring chambers.
three
Drill a minor hole in the license plate mounting expanse. Make sure at that place are no obstructions between the license plate mount and the rear wiring sleeping accommodation. Then, create a modest hole in the motorcar using a power drill equipped with a high-speed twist drill bit. Line up your hole and then information technology is directly behind where your photographic camera's ability and video cable will go.^[6]
- To figure out where to make the pigsty, hold your camera upward to the area yous intend to mountain it. Then, note the spot where its splitting cord sits.
- Create a hole that'due south big plenty to fit your camera'south power and video cable.
- If you come across whatsoever obstructions, try to remove them. If you tin't, meet if yous can make a hole nearby.
- For most jobs, y'all'll need a drill scrap that has a diameter between ^ane⁄_viii and ¹⁄_four in (0.32 and 0.64 cm).
iv
Place a prophylactic grommet around your camera cablevision. Before running your camera cable into the automobile, slip a rubber grommet onto it about the non-splitting finish. These small rubber washers, available at most home improvement stores, will go on the wire in place and forestall leaks.^[7]
- Choose a grommet that's just large enough to fit inside the drilled hole.
5
Run the camera cablevision into your trunk. Pull the splitting stop of your photographic camera's video and power cable through the drilled hole into the body of your car. Make sure you lot pull it tight then the rubber grommet lodges into the drilled hole.
- Your photographic camera cable should run from the outside of the car to the inside of the car.
6
Locate your car'south 2 reverse low-cal wires. Reverse light wires are the cords that connect your car'due south tail lights to the dashboard. They hook directly into your vehicle's tail lights and are commonly located in the hatch or body of your car.
- These cords look different for every vehicle and so, if you can't discover them, consult your possessor's manual for model specific information.
7
Strip and separate your automobile'south opposite light wires. Using a wire stripper or pliers, peel back the rubber roofing the wires. And so, apply a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the individual wire strands.^[eight]
- For safety, brand sure y'all practice this while the car is turned off.
8
Fuse your camera wires with the reverse light wires. Attach ane of your blank wire cables to the camera cord's power connector. Then, poke your bare wires through the center of the exposed reverse light wires and twist them together. For safety, make certain you wrap the combined wires in electrical tape.^[9]
- Brand sure you lot poke your positive (normally scarlet) bare wire through the positive reverse low-cal wire and the negative (usually black) bare wire through the negative reverse light wire.
Advertisement

ane
Road your camera'southward video cable to the forepart of the machine. Connect your RCA cable to the camera cord'south video connector if necessary. So, run information technology through your vehicle to the area by the fuse box. Depending on your vehicle model, you'll unremarkably be able to exercise this by peeling back the automobile'due south headliner or side panels and pulling your cable through the exposed sleeping accommodation.^[10]
- For certain trucks, yous may demand to run the video cable through the vehicle's frame rail.
- In most cars, y'all'll notice the fuse box underneath the steering cycle.
2
Gear up external monitors to the front windshield. If you lot're installing an external monitor, offset attach your device's included mountain to the windshield past following the manufacturer's included instructions. Then, hook your monitor onto the mount.
- Most external monitors use a suction mountain, though others may come with a more than complex mounting arrangement.
3
Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll demand to clip the new device onto your current rear-view mirror. For others, y'all'll demand to take off the mirror and slide your monitor into the pre-existing mirror mount.^[11]
- Some internal monitors may come with their ain mounting organisation that you'll take to attach to the machine's forepart windshield.
four
Run the monitor's splitter cable to the fuse box. If necessary, hook your monitor's power and video cable into the device. Then, route the cablevision from the monitor to the area side by side to the fuse box.^[12]
- If you lot'd like, use a trim removal tool to pop out the headlining panel direct higher up your windshield. Then, run your cablevision through the exposed chamber.
5
Connect your monitor's camera cable to the RCA cable. After routing your monitor's splitter cable, connect the video terminate of the cable to your camera's RCA cord. And then, wrap the connected cords with electrical tape to hold them together.
- If your RCA and video cables have the same ends, you may demand to purchase an RCA male to female person converter cord. You can detect these at most electronic stores.
half-dozen
Attach your monitor's power cable to a fuse tap. Connect your remaining bare wire cable to the backup monitor'due south power cord. Then, button the positive (usually red) end of the bare wire cable into the open end of a fuse tap. Finally, crimp the two cables together with a pair of pliers.^[13]
- A fuse tap is a small cable that converts a bare wire into a fuse betoken. You tin can find them at about auto part stores.
- If yous'd prefer, y'all tin leave the blank wire cable off and connect your camera's ability cable to a cigarette lighter adaptor. Then, plug this adaptor into your motorcar's cigarette lighter receptacle for power.
7
Plug the fuse tap into the fuse box. Locate your fuse box and open it upward. Then, plug your fuse tap into an open fuse jail cell. If necessary, check your fuse box's lid or your vehicle'due south instruction manual to see which slots are open.^[14]
- Afterwards attaching your fuse, consider taping all your wires together using electrical tape to get them out of the way.
Advertisement

one
Connect your fill-in photographic camera to its power and video cable. Render to the back of your automobile once yous've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, then connect the backup camera to its ability and video cable.
- Your camera'south power and video cable should be sticking out of the hole y'all drilled in the license plate mounting area.
ii
Mount the camera to your license plate. If the camera attaches to the front of your license plate, fix information technology to the plate by following the manufacturer'due south included instructions. If the photographic camera attaches to the dorsum of your license plate, line the device up with the plate's fastener holes and thread screws through them.^[15]
- In almost cases, y'all tin attach a rear-view camera to the dorsum of your license plate using the screws you removed from the car earlier.
3
Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once you've reattached information technology, give the license plate and backup camera business firm tugs to make sure they're secure.
- If you haven't already, reattach your automobile'south interior body panel and other trim panels by pressing them back onto the vehicle.
iv
Test the camera to make certain everything works. Before using your new photographic camera on public roads, examination information technology in a prophylactic expanse like your driveway. If it turns on, place a large, durable object like a trash can behind the camera to see how distorted the epitome is. If it does non turn on, read your installation manual for troubleshooting data.
- In many cases, rear-view camera malfunctions are acquired by loose or improperly connected wires.
Advertisement

Add New Question

Question

I hooked the photographic camera up and it simply flickers. Any advice?

You lot may want to ensure all cables and connections are secured tightly. Double check that all connections are right. If this doesn't work, check to see if the camera chosen is in skillful shape and isn't physically damaged.
Question

Suzuki installed reverse parking camera in my Swift Dzire Zxi. But the photographic camera shows upper view and not the ground below. What tin can I do ?

Make sure that the photographic camera is installed the right way (not upside downward), and check the position of the camera mounted. Take it back to the dealer that installed information technology and ask them to bank check the alignment and fit.
Question

What is the best top for a reversing camera?

There is no optimal height for a back-up camera. The ideal summit is based off the specific car or vehicle that you lot have and your personal preferences, along with its intended application. Some back-upward cameras are placed on large service trucks and then that they can line upwardly to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your awarding, it can be placed at whatsoever height. Most reversing cameras are a "wide view" way and the specific height location does non always affect the way it functions.

Ask a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Though nearly car dealers and mechanics will not install aftermarket backup camera systems, many sound and electronic shops will.

Make sure you turn the car off before working with bare or stripped wires. If you demand to touch exposed wires while the car is on, put on a pair of shock-resistant prophylactic gloves.

Things You'll Need

Rear-view camera
Rear-view monitor
Connector cables
Phillips caput screwdriver
Trim removal tool
Power drill with high-speed twist fleck
Safety grommet
Wire stripper or pliers
Electric tape
Fuse tap

Nigh This Commodity

Article Summary X

To successfully install a rear-view camera, first remove your vehicle's rear license plate and interior trunk console. Using a power drill, dial a small pigsty through the exposed license plate mounting area and run your camera's power and video cord through it. Attach a bare wire power cable to your camera's power connector, and so strip your motorcar's reverse calorie-free wires and splice them with your blank wire ability cable. To acquire how to mountain the rear-view camera and backup monitor, scroll downward!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 245,526 times.